ChaosVPN:Netbsd NAT VPN router using chaosvpn and ipnat

Basic setup after a vanilla install of NetBSD 5.2

If you want to set up a small network of computers on chaosvpn behind a NetBSD 5.2 router, this is the document for you. The purpose of this document is a step-by-step process to install and configure a VPN router that will serve as a router or firewall for a number of computers behind NAT with a single, external (to the chaosvpn) IP address. This document will assume that addresses on the LAN computers are all staticly assigned (ie no DHCP).

Note:

Your internal and external IP addresses will (hopefully) not be the same as the author's. Please substitute the correct ip addresses for your internal and external interfaces. Also your internet DNS server will also likely be different.

Still a work in progress.

To do:

Stuff on Carp redundancy? pf?

Setup pkgsrc and networking

Set up pkgsrc repository

Edit the file /root/.profile

Change the path for the pkgsrc repo to:
ftp://ftp.netbsd.org/pub/pkgsrc/packages/NetBSD/i386/5.0/All/

The file will be read-only, use :wq!

Set up network interfaces

Edit the file /etc/ifconfig.fxp0

This will the the external (wan) interface.

Insert the contents:

192.168.0.201 netmask 255.255.255.0 

Edit the file /etc/ifconfig.fxp1

This will be the internal network (lan) interface.

Insert the contents:

10.100.44.2 netmask 255.255.255.0

Ensure IP forwarding is set up

Edit the file /etc/sysctl.conf

Insert the contents:

net.inet.ip.forwarding=1

Specify your DNS server

Edit the file /etc/resolv.conf

Insert the contents:

nameserver 64.59.184.13

Specify basic settings in rc.d to set up networking

Edit the file /etc/rc.conf

Append the following to the end of the file:

hostname=yourhost.yourdomain.net
defaultroute=some.ip.address.here
sshd=yes

Create a new user to do tasks that don't require root

# useradd -m -G wheel chaosvpn_user
# passwd chaosvpn_user

Continue with the installation of ChaosVPN

Continue with the steps at:

https://wiki.hamburg.ccc.de/ChaosVPN:NetBSDHowto

---

IPfilter setup

IPfilter is installed by default on Netbsd 5.2.
No special packages are required.

Configure ipfilter startup settings

remove this next bit later if testing shows that statically linking in kernel actually works

Set ipfilter to run by default

Edit the file /etc/rc.conf

Append the following to the end of the file:

ipfilter_enable="YES"
ipfilter_rules="/etc/ipf.rules" 

ipmon_enable="YES" 
ipmon_flags="-Ds"

gateway_enable="YES" 

ipnat_enable="YES" 
ipnat_flags="CF"

Set up ipfilter to log

For now, we want ipfilter to log

# touch /var/log/ipfilter.log

Edit the file /etc/syslog.conf

Append the following to the file:

local0.* /var/log/ipfilter.log

Set up IPNat rules

Edit the file /etc/ipnat.rules

Insert the following:

map fxp1 10.100.0.0/16 -> 0.0.0.0/32 portmap tcp/udp 10000:20000
map fxp1 10.100.0.0/16 -> 0.0.0.0/32

---

Other Setup

At this point in the game, you should have a functional router for your NAT chaosvpn network. The "fxp0" interface should be connected to the Internet, and the "fxp1" interface should be connected to your hub or switch for the internal network (ie, the stuff behind the NAT).

Set up the network machines with the gateway address 10.100.44.1.

You should be able to browse chaosvpn from your local network !